First, the web slitter boot

1. Turn on the EMERCENCY STOP RESET and the READY TO RUN button. Turn on the MACHINE to the RUN (main stage) and check the voltage (380V). The current is correct and stable. 1. Turn on the electric isolation switch (set in front of the electric control cabinet).

2, open the hydraulic system power switch (set in the main hydraulic drive frame), check the main hydraulic drive system oil level and pressure gauge display is correct and stable.

3, open the pneumatic shut-off valve (set in the pneumatic control cabinet intake pipe), check the air pressure is correct (not less than 6.0bar less), stable.

Second, the web slitter set control

1, according to sub-film type single-cut plan to arrange the thickness, length, slit width setting menu.

2. Lift the corresponding document from the PDF BOPP film.

3, the length of the corresponding specifications set to rewind the film, width.

4, select the appropriate winding station, adjust the pressure roller and pressure roller arm, install the appropriate size of the paper core.

Third, the web slitter feeding, through the film, and then the film

1, feeding: reduction plan, in accordance with the individual requirements, in accordance with the traffic rules, according to the actual situation, in the time hanging shelf to take the appropriate parent volume, according to corona surface inside and outside the selection direction on the United States and the United States roll cutting machine roll Frame, and with the control button clamping steel core, steel core support arm and left lane.

2, transmembrane: If there is no film, easy-to-roll web slitter should be carried through the film. The use of the United States and the United States Yi-roll cutting device through the membrane device and function keys, the film will be linked to the end of the original film in the eye, Kai

Moving through the membrane button to film along the cutting process to the formation of the distribution in the roll.

3, and then the film: When the web slitter film, roll gap, in the use of vacuum sealing membrane sleeve, the first set of film to start working position, the United States and the United States Yi Mei roll cutting machine on the first traction roller The film is flattened and the upper vacuum pump suction and membrane is formed to allow access to the film stage, affixing the double-sided tape and cutting off the excess film under the tape, flattening the film on the unwinding stand and starting the lower vacuum pump So that the film flat adsorption, scoring in the tape layer and smooth film, seams should be neat, wrinkle-free, and then turn off the vacuum pump, Taiwan will open the film on the non-working position.

Fourth, the roll paper cutting machine starts to move

1, to improve the specifications, inside and outside the arm around the new good, the pressure roller in the run-ready state to notify all personnel to leave the machine, ready to run.

2, the main console ANTI-STAIC BARS placed AUTO, READY TO RUN opened, start the machine to run the boot operation.

Fifth, the web slitter cutting control

During the slitting operation, carefully monitor to observe the running cutting effect, the correct cutting speed, unwinding tension, contact pressure and bending roller, traction edge material, the edge of the guide to adjust the appropriate control.

6, the volume sub-cut rewinder

1, on the inside, the outer end of the winding machine to stop the operation is completed, the use of unloading membrane button on the film to be prepared on the unloading car, cut off the film and seal the film with a good paste.

2, release the button to use the suction head to loosen the video card, check the film roll core if not new, if the head still stuck on the paper core is to manually remove the film.

3. Ensure that all the film leaves the chuck of the small car, the button to enhance the use of the loading arm of the winding arm, the installation of the corresponding core, the film is neatly attached to the core, once cut off one.

Seven, Web Slitter Parking

1, when running to set the length of the film, the device will automatically stop.

2, in the operation of the device, according to the need to process STOP parking.

3, when you need to quickly stop, press the MACHINE STOP key is greater than 2S.

4, when there is an accident, such as equipment or man-made emergency, according to emergency stop emergency stop.

Eight, precautions

1, to ensure that the voltage before the current and hydraulic equivalent is correct and stable.

2, the equipment ready to run, all personnel must inform the departure of equipment to ensure the safety of people before the start of operation.

3, easy to US-web slitter in operation, avoid touching the operation of the film roll or roll core, so that it will not harm the hands involved.

4, during operation, to avoid knife or hard object scratch, cross-cutting roll core.